|
|
|
BTM-01 StarCom1 Bluetooth Module
Introduction
Measuring only
1¼" x ¾" x 1¾"
Install with Starcom1, then leave
your bluetooth enabled phone in your
pocket, it will automatically
connect each time you get on the
bike.
The Starcom1 bluetooth module is
designed to allow cordless and
automatic operation of bluetooth
compatible mobile phones with the
StarCom1 unit.
Bluetooth is a short- range wireless
communication technology. It allows
wireless connections between Bluetooth
devices such as cellular phones,
personal digital assistants (PDA),
desktop and notebooks computers,
input-output devices (mouse, keyboards,
printers), home appliances. Bluetooth
refers to a worldwide standard designed
to operate in the internationally
recognized ISM (Industrial Scientific
and Medical) frequency band. Within the
ISM band (2.4Ghz - 2.48Ghz) Bluetooth
transmissions hop between 79 separate
frequencies 1,600 times every second,
and with a communication range of about
10 meters (class II).
Bluetooth
Class 2 product with compliance to
specification v11.1 and full FCC and CE
certification.
Installation instructions must be
followed carefully.
Installations must only be undertaken by
a person who has a full understanding of
the electrical, safety and mechanical
requirements involved. If in any doubt,
please consult your dealer.
Unit Installation
The unit must be operated from a
switched vehicle 12V DC supply. The
unit is water-resistant but not
waterproof so care must be taken to
keep it dry. Care must be taken not
to mount the unit near areas which
will get hot, for example, near the
engine or exhaust. Also the unit
must not be placed close to the
ignition system; HT leads coil,
alternator, or parts of the bike
that could cause electrical
interference.
Power Cable Installation
The unit requires a 12V vehicle
supply it has a built-in voltage
regulator, reverse input protection
and fuse, so that it is safe to use
directly from a vehicle’s switched
supply. A power cable is supplied
along with an in-line fuse and
fitting kit.
The 12V supply must be ignition
switched, so that the BTM-01 supply
is off when the vehicle ignition if
OFF else the vehicle battery may be
drained.
The Jack plug cable must be plugged
into the phone socket on
Starcom, this provides the 0V
connection.
1) If the StarCom 12V supply is
ignition switched supply then the
BTM-01 12V connection can be made by
splicing into the starcom power
cable.
2) If the StarCom is connected to
the battery directly then the
BTM-01module must be connected to a
switched supply.
Pairing Headset
You are required to pair the BTM-01
with your mobile phone or other
devices before using it.
Step 1: The BTM01 must be connected
to StarCom and powered ON before
initiating pairing. To initiate
pairing, press and hold pairing
button for 5 seconds until the red
indicator of BTM-01 is slowly
flashing.
Step 2: Initiate pairing process of
your mobile phone. Refer to the
manual of mobile phone for details
of the process. You will see a new
item "StarCom1" added in your
Bluetooth device list after the
searching process completes.
Step 3: You will be asked to enter
pin-code to complete pairing, enter
0000 and confirm it. (Note:
The 0000 is default pin-code
pre-stored in BTM-01.) The red
indicator will turn off after
pairing completed successfully.
Note:
1. If the BTM-01 is not in pairing
mode, your mobile phone won't find
the BTM-01.
2. You may need to repeat steps 1 to
3 until pairing succeeds.
3. Pairing is a process of
associating Bluetooth devices with
each other. It will establish a
permanent security link between the
devices and enable quick access to
the services provided without the
need to enter passkeys.
4. Paired devices remain paired even
when:
- One of the devices is not powered
on.
- A service connection is
interrupted or the service stopped.
- One or both devices are rebooted.
Fitting Kit
5x short tie wraps 1x scotch lock
splice 1x loop Velcro 1x hoop
Velcro |
|
|
